Tuesday, if first you dont succeed, dust yourself off and try again.

-
I'll recap the events of today.

- woke up
- went to gym
- came home
- surfed the net
- showered
- made breakfast
- surfed the net while eating said breakfast
- went in the garage
- opened garage door
- facepalmed

Because I'm here in the garage again.



I tucked the resistor in the male half of the sensor plug and then taped it in rather than soldering it.






After all of that pressing stuff I decided I wanted to do something aesthetic and lowered the front coils about 1in each side, I'm much happier with the wheel to fender gap now although my bumper wont be happy with the inch of lost clearance getting in and out of my driveway.




Much better



another bland shot of the front.



The clips that hold the kouki front grill are all broken pretty much so to prevent me from constantly having to zip-tie and un zip tie it I am just leaving it off until I have the car painted.

Done and Done.




I was going to take the car for a test run, but I guess that will have to wait for another day.

Popular posts from this blog

Wiring an S13 SR20DET up for an S14 (95-98)

-
Image
If you've come here then you have decided to undertake the task of wiring up an s13sr20det motor for use in a 1995-1998 240sx. This isn't the end all guide or going to go over problem free for you if it's your first time wiring up an engine. But it will get you set on the right path. - Wayne Tips before you get started on buying stuff. make sure you only use adhesive heat shrink. Just so happens a strand of h/s I bought wasn't adhesive and the solder ended up corroding causing shorts/issues. I had to cut open the whole harness and replace all of the heat shrink to be sure.  Extra runs of wiring aren't really necessary to do this, you can use wires from your ka24de harness that are already color matched and the same gauge.  The s13sr20det harness can have about 3-4 inches removed from it behind the firewall (in car) but don't make any cuts until you know everything works, then shorten as desired.  If you break a plug/connector (use your brain a...
Read more

Almost there!

-
Image
Just gonna do a random photodump and just chat about some things. Embedding some you tube shorts as well. I previously mentioned how I was going to upgrade to hid's and led corner lights and turn signals. But I also wanted to black everything out, light output at night shouldn't be affected. May be a bit harder to see things during the day but I'm not too worried about it. The oem stuff was already pretty hard to see during the day anyway as shown in the example below.  So here is the final result of the headlight and corner light tint, I still have my old oem signal markers in. I was waiting to pick up my led ones from paint as there just was no way I was going to be able to wrap them. Going to try and retain the ability to plug in oem stuff rather than discarding the wiring for strictly led items in case I need to replace anything with off the shelf parts.  This is the oem connector for the corner lights, I have my chassis harness sleeved and loomed in the engine bay and ...
Read more

RX330 Projectors, Dancing Led Signals, and Blackout Tint

-
Image
This is going to be a three part blog of some sort. I had been traveling to the 240 tuesday meets which are about 60 miles away from me and I head home to a lot of freeway and road construction so I can't see a damn thing. Normally I've never had any issues with my halogen projectors on the kouki headlights. But I've always been curious about doing an HID swap.  After seeing Hugo's s14 with dancing leds on his Zenki I was curious about getting some done for my car. I've always wanted some kind of led lights, but clearcorners.com lights were just never in my budget even though Mike Mamos is an acquaintance. I don't ask for discounts at friends businesses, I spend money elsewhere like a true piece of shit. HAHA Hugo's S14 I really like the look of the blacked out headlights mainly because the led corners and turn signals are built in a manner where there is like a piece of tape that's put over the area where the oem light would sit and holes are poked in i...
Read more