Photodump @ Jordan Innovations

-
in the shade cold chillin in beautiful Irwindale

Tire to rear overfender clearance

rear of the tire is cutting it SUUUUUUUUPER close. Toe is in spec and cars thrust angle is straight so I can't really dial any camber out. It will rub with a proper 265 on the back. 

another edge I'll have to cut. 

the executive decision to jam rivets into the side skirts were made after the realization zip ties were no longer an option here. I'll have to cut this off at a later time. 

chips ahoy (the doors were not re-painted) 

Not too sure why the doors are making contact here but gonna have to grind these down with the dremel and hit it with touch up paint. 

Need to make debris guards for the front fenders, rocks get caught up here after it rains and makes a sound that would make a grown man cry when you open the door and hear those rocks munching at your paint!!! 

The corner is on this hood haha! yes, look at that line up. Shits money, fuck removing this hood again! 

the fitment after the repairs however are money, no waves or bullshit! 

All cracks have been repaired. Just ran out of paint to do the bottom. 

could shave this a bit and paint it eventually. 

whoever repaired the hood before used bondo instead of resin/fiberglass. Yeah that was stupid! 

more dremel work here, you can see the haze from wetsanding on fender still lol

gonna hit this with a dremel and just remove the upper half. 

god that hood is so money! 

2.6 degree's of front camber

4.2 degree's of camber

ass shot! 

Sideskirt has my body sweat on it! gross! 
Still working on this shit haha! 

Flex A Light Fan Controller, still can't handle the amp draw of a taurus fan on it's high setting, low it is. 

had to shave a bit of the gas door metal off for this to fit. 

Luckily there isn't a huge distance from the over and the body here so no worries about fucking up paint jamming a filler in here. 

Popular posts from this blog

Wiring an S13 SR20DET up for an S14 (95-98)

-
Image
If you've come here then you have decided to undertake the task of wiring up an s13sr20det motor for use in a 1995-1998 240sx. This isn't the end all guide or going to go over problem free for you if it's your first time wiring up an engine. But it will get you set on the right path. - Wayne Tips before you get started on buying stuff. make sure you only use adhesive heat shrink. Just so happens a strand of h/s I bought wasn't adhesive and the solder ended up corroding causing shorts/issues. I had to cut open the whole harness and replace all of the heat shrink to be sure.  Extra runs of wiring aren't really necessary to do this, you can use wires from your ka24de harness that are already color matched and the same gauge.  The s13sr20det harness can have about 3-4 inches removed from it behind the firewall (in car) but don't make any cuts until you know everything works, then shorten as desired.  If you break a plug/connector (use your brain a
Read more

S14 Digital Climate Control 2022 Redux

-
Image
Introduction  Hello,  So you wanna install one of these. I'll try to be the voice of reason in 2022 and tell you it's probably not even worth it. 10-15 years ago, heck yeah go for it.  But if you're insistent like myself, I'll give you all of the tools needed to get the job done.  It's been a while since I've installed this. 12 years in fact. I've contemplated making youtube videos but to be honest I am ungodly lazy. This blog post at this point is more of a diary for me as well as a how-to because if I ever have to troubleshoot this crap again I know that I've unnecessarily over-documented this install for the final time.  I will say that, I originally followed the write up here:  chuonthis s14 dcc write-up  I don't want to plagiarize and flat out copy the write up, but I'm going to stage the information very similarly.  I have it available in PDF format and have uploaded it here in case their website ever goes down. I recommend saving that.  O
Read more

RX330 Projectors, Dancing Led Signals, and Blackout Tint

-
Image
This is going to be a three part blog of some sort. I had been traveling to the 240 tuesday meets which are about 60 miles away from me and I head home to a lot of freeway and road construction so I can't see a damn thing. Normally I've never had any issues with my halogen projectors on the kouki headlights. But I've always been curious about doing an HID swap.  After seeing Hugo's s14 with dancing leds on his Zenki I was curious about getting some done for my car. I've always wanted some kind of led lights, but clearcorners.com lights were just never in my budget even though Mike Mamos is an acquaintance. I don't ask for discounts at friends businesses, I spend money elsewhere like a true piece of shit. HAHA Hugo's S14 I really like the look of the blacked out headlights mainly because the led corners and turn signals are built in a manner where there is like a piece of tape that's put over the area where the oem light would sit and holes are poked in i
Read more